Speaking of the soldering machine electronics industry is very common, there are many types and specifications of automatic soldering, in Dongguan you can also develop and produce according to your needs. The size of solder components is also different, so the proper and reasonable choice of power and type of soldering machine is the top priority, which is of great significance to the quality and efficiency of soldering.
The solder joints should not be too saturated. They should be in the middle of three or four points. Otherwise, the solder joints will be easily disconnected from the solder joints next to each other. The solder must be in a small semicircular shape with the component pins. . In addition, the lead of the soldering machine must not be too thin or too long, the voltage drop during welding must not be greater than 5% of the initial voltage, and gloves, protective glasses, etc. must be worn during operation.
There are many types and specifications of soldering machines, and the sizes of the workpieces to be welded are different. Therefore, the reasonable selection of the power and type of soldering machines has a direct relationship with improving the quality and efficiency of soldering. When soldering soldering integrated circuits, transistors, and thermally vulnerable components, a 20W internal heating or 25W external heating soldering machine should be used. When soldering wires and coaxial cables, first use a 45W ~ 75W external heating type soldering iron or a 50W internal heating type soldering machine. When welding larger components, such as lead pins of line output transformers, lead pins of large electrolytic capacitors, ground pads of metal chassis, etc., a soldering machine of more than 100W should be used. The soldering iron of the soldering machine must be heated enough before it can be produced, which is also a matter of more virtual soldering.
The lead of the soldering machine should not be too thin or too long. The voltage drop during soldering must not exceed 5% of the initial voltage, and the initial voltage must not deviate from the power supply voltage by ± 10%. Gloves, apron and protective glasses should be worn when the welding machine is operated, so as to avoid scalding from the sparks. The sliding part should be kept well lubricated and the metal splash should be removed after use. After the new welding machine is used for 24 hours, the screws of each component should be tightened once. Pay particular attention to the fastening screws between the copper soft coupler and the electrode. After use, the oxidation between the electrode rod and the electrode arm should be removed frequently. To ensure good contact. If the soldering machine is found to be inaccurate when the AC contactor is in use, it means that the voltage of the power grid is too low. The user should first solve the problem of the power supply before the power supply is normal. It should be pointed out that if the newly purchased welding machine has a quality problem of the main part within half a month, it can be replaced with a new one or the main part can be replaced. The main part of the soldering machine is guaranteed for one year and provides long-term maintenance services. Generally, after the user informs the factory, the service will be available within three to seven days according to the distance. Welder damage due to user reasons is not covered by the warranty. Consumables and consumables are not covered by the warranty.
When soldering the soldering machine, the solder joints cannot be too saturated, and the solder joints that are too large are likely to be disconnected from the adjacent solder joints. When soldering, the solder joints should not be too tin-saving, which leads to false soldering. The correct soldering point of the soldering machine is in the middle of three or four points. The solder must be in a small semicircle with the component feet, which is not saturated or tin-saving. In this way, the contact of the solder point to the component is the best. The circuit board is also the most neat. The soldering machine uses an adjustable constant temperature soldering iron. When the soldering iron is not in use, keep a certain amount of tin on the tip of the soldering iron. Do not store the tip on the sponge after cleaning it on the sponge. Measure the amount of water to make the sponge moist all day long; when you pick up the soldering iron and start using it, you need to clean the tip of the soldering iron.
During the use of the soldering machine, there is no need to take the soldering iron tip to the sponge to clean, just put the tin on the soldering iron tip into a tin-collecting carton, so as to keep the temperature of the soldering iron tip from dropping rapidly. Extraction of tin is difficult. Adding some tin up (due to the flux contained in the tin wire), you can easily extract more tin. The temperature of the soldering iron is between 340 and 380 degrees, which is normal. Some sensitive components are only acceptable. Soldering temperature of 240 ~ 280 ° C. The soldering iron tip is very beautiful. It can not be treated with metal devices such as blades, but should be solved with tin wire. After using it every day, clean it first, add enough tin, and then cut off the power immediately.
Soldering robots are used in the electronics manufacturing industry. They are mainly targeted at processes that are difficult to achieve with production equipment such as reflow soldering and wave soldering. They are particularly suitable for the welding of sensitive components in mixed circuit boards, heat-sensitive components, and SMT back-end processes. Soldering robots replace manual welding to improve work efficiency and improve welding quality.
1. Used for welding various electronic components and wires, with spot welding and drag welding functions.
2. Mass storage, to meet all needs, can store 9999 models, each model can be set to 999 steps.
3. With 4-axis position movement and 1-axis automatic tin-out function.
4. Password protection function to ensure system and model parameters are safe and reliable.
5. The single step and test step functions are convenient for tuning test.
6. The calibration function is used for position calibration after the parameters of different machines are copied.
7. Available in Chinese and English.
8. Has a variety of flexible model debugging and editing methods.
9. Automatic cleaning of welding head function.
10. Functions can be customized according to customer needs.
Dongguan Chuangxiao Automation Technology Co., Ltd. © All rights reserved
Phone: 0769-85825590 E-mail: email@example.com
Address: 2nd Floor, Building B, Dinghao High-tech Industrial Park, No.29 Baohong Road, Baotun Community, Houjie Town, Dongguan City
Scan, watch on mobile